Properties of starch–cellulose fiber films produced by tape casting coupled with infrared radiation

Tape casting is a suitable process for large-scale production of biodegradable films. This study presents a comparison of three drying procedures of starch–cellulose films: i) conduction drying, ii) infrared drying (42.3?W?m^?2, higher infrared heating power damaged the films), and iii) conduction-infrared drying. All the drying procedures were performed at approximately 60°C. Drying times from the second and third methods were close to 1?h, half the time observed for conduction drying. Films from the second and third methods showed similar hygroscopicity (0.15?g.?g^?1, RH 43%), tensile strength (31.3?MPa, RH 58%), and glass transition temperature (?12.13°C, RH 43%).     

Improved properties of scandia and yttria co-doped zirconia as a potential thermal barrier material for high temperature applications

Due to the limited temperature capability of current YSZ thermal barrier coating (TBC) material, considerable effort has been expended world-wide to research new candidates for TBC applications above 1200?°C. Our study suggested that Sc₂O₃ and Y₂O₃ co-doped ZrO₂ (ScYSZ) had excellent t’ phase stability even after annealed at 1500?°C for 336?h. The thermal expansion coefficient of ScYSZ was comparable to the value of YSZ. The thermal conductivity of fully dense ScYSZ was in the range of 2.13–1.91?W?m^?1?K^?1 (25–1300?°C), approximately 25% lower than that of YSZ. Although the fracture toughness of dense ScYSZ was slightly lower than YSZ, an evident decline in elastic modulus was found. Additionally, thermal cycling lifetime of plasma sprayed ScYSZ coating (914 cycles) at 1300?°C was about 2.6 times longer than its YSZ counterpart. The superior comprehensive properties confirm that ScYSZ is a prospective candidate material for high-temperature TBC application.     

Prolong the durability of La2Zr2O7/YSZ TBCs by decreasing the cracking driving force in ceramic coatings

Service lifetime and thermal insulation performance are both crucial for the application of thermal barrier coatings (TBCs). In this study, layered structure design under equivalent thermal insulation conception is introduced to lower the cracking driving force in TBCs, and with the goal of prolonging TBCs lifetime. Three groups of layered LZO/YSZ TBCs were designed with same thermal insulation of 500?μm YSZ, the LZO layers were deliberately designed with different initial elastic modulus. Virtual crack closure technique (VCCT) calculation result showed that the energy release rates at the crack tips are 28.2, 22, and 18.8?N/m corresponding to the initial elastic modulus of 70, 60, and 50?GPa. After gradient thermal cyclic tests with surface temperature of 1300?°C, TBCs with lowest initial elastic modulus showed the longest lifetime, and more than double of pure YSZ TBCs. This study provides a new option for the improvement of TBCs lifetime.     

Phase equilibria in the zirconia–yttria/gadolinia–silica systems

Phase equilibria in ZrO₂-YO_1.5-SiO₂ (ZYS) and ZrO₂-GdO_1.5-SiO₂ (ZGS) were experimentally assessed at 1400?°C and 1600?°C as they can offer insight on reactions between thermal barrier coatings (TBCs) based on ZrO₂-YO_1.5/GdO_1.5 and molten silicate deposits in gas turbine engines. Features shared in both systems include the absence of ternary compounds and no ternary solubility in the binary phases. In ZYS however, a quaternary invariant reaction was observed that eliminates the zircon-disilicate equilibrium at higher temperatures. The results suggest no appreciable difference in the reactions between silica and thermal barrier oxides based on ZrO₂-YO_1.5 or ZrO₂-GdO_1.5, or environmental barrier coatings based on the corresponding Y/Gd silicates. The phase diagrams derived from these experiments are part of a broader effort to develop thermodynamic databases that can help guide the design of next-generation TBCs.     

Wetting,infiltration and interaction behavior of CMAS towards columnar YSZ coatings deposited by plasma spray physical vapor

Thermal barrier coatings (TBCs) produced by electron beam physical vapor deposition (EB-PVD) or plasma spray (PS) usually suffer from molten calcium-magnesium-alumino-silicate (CMAS) attack. In this study, columnar structured YSZ coatings were fabricated by plasma spray physical vapor deposition (PS-PVD). The coatings were CMAS-infiltrated at 1250?°C for short terms (1, 5, 30?min). The wetting and spreading dynamics of CMAS melt on the coating surface was in-situ investigated using a heating microscope. The results indicate that the spreading evolution of CMAS melt can be described in terms of two stages with varied time intervals and spreading velocities. Besides, the PS-PVD columnar coating (～100?μm thick) was fully penetrated by CMAS melt within 1?min. After the CMAS attack for 30?min, the original feathered-YSZ grains (tetragonal phase) in both PS-PVD and EB-PVD coatings were replaced by globular shaped monoclinic ZrO₂ grains in the interaction regions.     

固溶处理对节镍型2101双相不锈钢组织及力学性能的影响

采用光学显微镜、透射电镜和X射线衍射等研究了固溶处理对2101节镍型双相不锈钢连铸坯边部试样的组织、相比例和力学性能的影响。结果表明:在1050~1150℃固溶处理时,双相不锈钢具有很好的高温塑性;在1000~1150℃温度范围,随着温度的升高,实验钢的断面收缩率和铁素体相比例先减小后增加;随着固溶温度增加,实验钢的抗拉强度逐渐降低,但在1050℃时有所增加,这是由于在此温度固溶过程中,铸态试样相界处Cr2N析出相完全溶解,使得大量的N原子集中在相界处,促进了相界附近的铁素体相发生相变,转变成奥氏体相,导致在此1050℃时实验钢铁素体相的比例减小,断面收缩率减小,抗拉强度增加。     

Fabrication of ZnO-functionalized polypyrrole microcomposite as a protective coating to enhance anticorrosion performance of low carbon mild steel

In the present work, PPy, ZnO, and polypyrrole/zinc oxide (PPy/ZnO) microcomposites (1, 2, and 5 wt%) were prepared and their properties have been tuned for anticorrosion applications on low carbon mild steel. The synthesized products: ZnO, PPy, and composites were characterized by various sophisticated analytical techniques such as XRD, FTIR, Raman, FESEM, EDX, UV–VIS, TGA, and BET. The band frequencies observed at 480 and 588 cm⁻¹ in FTIR spectrum correspond to stretching vibrations of Zn-O and N-H bonds, respectively, broadening of the bands in the composites indicate strong interactions between ZnO and PPy matrix. The potentiodynamic polarization study of PPy and PPy/ZnO composite was carried out in 3.5% NaCl solution to investigate the corrosion resistance efficiency. PPy/1 wt% ZnO (I_corr = 190 nA) composite coating on low carbon mild steel was observed to exhibit best corrosion protection property compared to PPy (121 μA), 2 and 5 wt% ZnO (242, 295 nA) composites. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48319.     

Innovative conductive polymer composite coating for aircrafts lightning strike protection

A new kind of high electrical conductive epoxy coating with low filler rate was investigated for lightning strike protection (LSP) of carbon fiber reinforced polymer (CFRP). The coating without CFRP substrate was firstly studied. The influence of silver submicronic wires (AgSWs) with a high aspect ratio on the electrical behavior is observed; that is, the electrical resistivity evolution, the current density value, and the electrical conduction mechanisms as function of temperature. The preponderant electrical conduction mechanism is an Ohmic behavior. The higher level of conductivity obtained is 5.5 × 10⁵ S m⁻¹ for 9% vol of AgSWs. Lightning strike tests were carried out on an epoxy/AgSWs coating filled with 8% in volume (74 gsm) and deposited on a CFRP. The ultrasonic testing after lightning strike on coated CFRP shows no structural delamination and demonstrates the interest of this new route for an efficient LSP. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 137, 48700.     

Anticorrosion reinforcement of waterborne polyacrylate coating with nano-TiO2 loaded graphene

Photocathodic protection coatings have been widely applied in various areas such as ship and architectural protection, or chemical industry. In this work, a composite of titanium dioxide loaded with reduced graphene oxide (RGO/TiO₂) was prepared and used as filler on waterborne polyacrylate (PA) coating to reinforce the metal protection against corrosion. Compared with the current filler of zinc phosphate used for anticorrosive coating, the photoelectrochemical properties of RGO/TiO₂-PA coating exhibit improved photocathodic protection under visible light illumination since RGO/TiO₂ composite has significant superiority in enhancing metal protection due to its dispersion, micropore blocking ability, and photoelectrochemical conversion performance. The mechanism of anticorrosion reinforcement of RGO/TiO₂-PA coating was hypothesized that graphene provides an extrabarrier layer to obstruct corrosive in dark condition and photocathodic protection under lighting. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48733.     

石墨烯改性涂层防护性能研究

为减少团聚，提高石墨烯在涂层中的分散性，研究采用纳米分散技术预先制备了石墨烯分散液，再将其分散至环氧树脂中获得石墨烯改性复合涂层。通过对石墨烯含量为 0、0.3%、0.6%的复合涂层进行盐水浸泡、盐雾、阴极剥离实验及电化学性能测试，证明石墨烯的加入显著增强了涂层的防护性能。石墨烯复合涂层在 3.5%盐水中浸泡 1 008 h后，涂层低频阻抗仍大于 106 Ω·cm²比未添加石墨烯的涂层提高了 3个数量级，且盐雾实验 6 000 h后涂层表面仍保持完好；含 0.6%石墨烯，的涂层耐蚀行为劣于石墨烯含量为 0.3%的涂层。